Before Starting Installation1. Carefully read all warnings and instructions completely before beginning.
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-7080.
4. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction.
Engine Compartment1. Measure and record distance between cab and bed.
2. Disconnect both battery cables. Disconnect negative cable first, then positive cable.
Prepare to Install Kit1. Apply appropriate amount of rust penetrant onto body mount bolts in advance. Repeat if necessary.
2. Loosen three driver side mount bolts.
3. Remove three passenger side mount bolts.
Install Kit
1. Using hydraulic floor jack, slowly lift passenger side cab sufficiently to remove O.E. body mounts and install kit bushings.
2. Remove three O.E. cab bushings from passenger side.3. Install kit bushings, kit washers, kit sleeves, and kit bolts (Position 2, 3) onto frame mounts.
3. Install kit bushings, kit washers, kit sleeves, and kit bolts (Position 2, 3) onto frame mounts.
4. Lower passenger side cab onto kit washers (Position 1) and kit bushings (Position 2, 3).
5. Clean and install three O.E. body mount bolts. DO NOT TIGHTEN.
6. Repeat above steps for driver side cab mount bushings.
7. Remove six body mount bolts and apply a small amount of Loctite® onto threads and install into each body mount.
8. Align cab to bed using previously recorded measurements and TIGHTEN body mount bolts to O.E. specification.
Dynamic Vehicle Check
1. Check steering in both directions to ensure that there is no bind. Check operation of clutch, brake system, and parking brake. Check operation of transmission and transfer case. Ensure there is full engagement in all gears and 4WD ranges. Check battery connections and electrical component operations. Test-drive vehicle.
Download Chevy P/U 1963-1966 Body Bushing Kit PDF Installation Instructions
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-7080.
4. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction.
Engine Compartment1. Measure and record distance between cab and bed.
2. Disconnect both battery cables. Disconnect negative cable first, then positive cable.
Prepare to Install Kit1. Apply appropriate amount of rust penetrant onto body mount bolts in advance. Repeat if necessary.
2. Loosen three driver side mount bolts.
3. Remove three passenger side mount bolts.
Install Kit
1. Using hydraulic floor jack, slowly lift passenger side cab sufficiently to remove O.E. body mounts and install kit bushings.
2. Remove three O.E. cab bushings from passenger side.3. Install kit bushings, kit washers, kit sleeves, and kit bolts (Position 2, 3) onto frame mounts.
3. Install kit bushings, kit washers, kit sleeves, and kit bolts (Position 2, 3) onto frame mounts.
4. Lower passenger side cab onto kit washers (Position 1) and kit bushings (Position 2, 3).
5. Clean and install three O.E. body mount bolts. DO NOT TIGHTEN.
6. Repeat above steps for driver side cab mount bushings.
7. Remove six body mount bolts and apply a small amount of Loctite® onto threads and install into each body mount.
8. Align cab to bed using previously recorded measurements and TIGHTEN body mount bolts to O.E. specification.
Dynamic Vehicle Check
1. Check steering in both directions to ensure that there is no bind. Check operation of clutch, brake system, and parking brake. Check operation of transmission and transfer case. Ensure there is full engagement in all gears and 4WD ranges. Check battery connections and electrical component operations. Test-drive vehicle.
Download Chevy P/U 1963-1966 Body Bushing Kit PDF Installation Instructions
Tidak ada komentar:
Posting Komentar