TOOLS NEEDED:
2.5mm allen wrench
10mm socket
13mm socket
10mm wrench
extension
flat blade screwdriver
ratchet
t-20 torx wrench
Drill motor
1/2” Drill Bit
TO START:1. Turn the ignition off and disconnect the vehicle’snegative battery cable.
2. Depress the locking clip on the mass air sensor electrical connection, then separate the mass air sensor electrical connection.
3. Depress the locking ring on the air pump fresh air inlet tube. Disconnect the fresh air inlet tube from the upper air box.
4. Loosen the hose clamp that secures the stock intake tube to the intake resonator.
5. Loosen the single retaining nut and two air box retaining bolts. NOTE: 2008 and later vehicles are not equipped with the mounting nut, all other vehicles will use the nut in a later step.
6. Lift the air box up, removing it from the vehicle as shown. NOTE: K&N Engineering, Inc., recommends that customers do not discard factory air intake.
7. Install silicone hose (08630) onto the intake plenum and secure with the provided hose clamp as shown.
8. Install “L” bracket (010060) onto the heat shield with the provided hardware as shown.
9. Install the small “L” bracket (070602) onto the heat shield using the provided hardware and spacer as shown.
NOTE: The spacer is to be placed between the bracket and heat shield.
10. Install the long edge trim onto the heat shield as shown. NOTE: Some trimming of the edge trim may be necessary.
11. Install the small edge trim into the heat shield hole as shown. NOTE: Some trimming of the edge trim may be necessary.
12. Install the provided adapter into the small heat shield hole as shown.
13. Install the provided air pump filter onto the adapter installed in the previous step. Secure with the provided hose clamp.
13a. On vehicles not equipped with the air box mounting stud and nut, drill out the existing hole in the inner fender with a ½” drill. 13b. Install the provided inserted nut into the hole drilled in step 13a.
14. Install the heat shield into the vehicle and secure with the provided hardware. NOTE: On vehicles equipped with the air box mounting stud the factory nut will be reused. The front of the heat shield will secure to the front air box mounting location. The rear of the heat shield will mount to the mounting stud with the factory nut or on 2008 and later vehicles will mount to the inserted nut installed in step 13b.
Note: Failure To Follow Installation Instructions And Not Using The Provided Hardware May Damage The Intake Tube, Throttle Body And Engine.
Download Chevrolet / GMC / Hummer 2007-10 Colorado / Canyon 2007-09 H3 L5-3.7L Air Charger High-Flow Intake Kits PDF Installation Instruction
2.5mm allen wrench
10mm socket
13mm socket
10mm wrench
extension
flat blade screwdriver
ratchet
t-20 torx wrench
Drill motor
1/2” Drill Bit
TO START:1. Turn the ignition off and disconnect the vehicle’snegative battery cable.
2. Depress the locking clip on the mass air sensor electrical connection, then separate the mass air sensor electrical connection.
3. Depress the locking ring on the air pump fresh air inlet tube. Disconnect the fresh air inlet tube from the upper air box.
4. Loosen the hose clamp that secures the stock intake tube to the intake resonator.
5. Loosen the single retaining nut and two air box retaining bolts. NOTE: 2008 and later vehicles are not equipped with the mounting nut, all other vehicles will use the nut in a later step.
6. Lift the air box up, removing it from the vehicle as shown. NOTE: K&N Engineering, Inc., recommends that customers do not discard factory air intake.
7. Install silicone hose (08630) onto the intake plenum and secure with the provided hose clamp as shown.
8. Install “L” bracket (010060) onto the heat shield with the provided hardware as shown.
9. Install the small “L” bracket (070602) onto the heat shield using the provided hardware and spacer as shown.
NOTE: The spacer is to be placed between the bracket and heat shield.
10. Install the long edge trim onto the heat shield as shown. NOTE: Some trimming of the edge trim may be necessary.
11. Install the small edge trim into the heat shield hole as shown. NOTE: Some trimming of the edge trim may be necessary.
12. Install the provided adapter into the small heat shield hole as shown.
13. Install the provided air pump filter onto the adapter installed in the previous step. Secure with the provided hose clamp.
13a. On vehicles not equipped with the air box mounting stud and nut, drill out the existing hole in the inner fender with a ½” drill. 13b. Install the provided inserted nut into the hole drilled in step 13a.
14. Install the heat shield into the vehicle and secure with the provided hardware. NOTE: On vehicles equipped with the air box mounting stud the factory nut will be reused. The front of the heat shield will secure to the front air box mounting location. The rear of the heat shield will mount to the mounting stud with the factory nut or on 2008 and later vehicles will mount to the inserted nut installed in step 13b.
Note: Failure To Follow Installation Instructions And Not Using The Provided Hardware May Damage The Intake Tube, Throttle Body And Engine.
Download Chevrolet / GMC / Hummer 2007-10 Colorado / Canyon 2007-09 H3 L5-3.7L Air Charger High-Flow Intake Kits PDF Installation Instruction
Tidak ada komentar:
Posting Komentar